Contains:

• Arduino ATMega 328
• Breadboard
• USB/Serial converter
• 9V battery clip
• 7805 5V regulator
• 2 ceramic capacitors
• 2 elcos
• 3 resistors
• 2 LEDs
• 16Mhz crystal

Sparkfun worked with their supplier to change how to thread is manufactured to decrease the fray-resistance. This new thread is more expensive but the quality and the fray-resistance has increased significantly. Now you can worry less about short circuits and worry more about your project.

This is a thicker thread with a lower resistance that can be used with hand sewing. Resistance is about 14 Ohms per foot. Spool contains 1oz of thread, about 75 yards.

The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of bend).

Straight (unflexed) resistance: ~9000 Ohm
90 degree bend resistance: ~14000 Ohm
180 degree bend resistance : ~22000 Ohm

Connector is 0.1" spaced and bread board friendly.

Documents:

* Datasheet
* ITP Sensor Workshop

This servo controller supports two separate communication protocols. One protocol is compatible with our other serial servo controllers and our serial motor controllers, and it offers individual range and speed control for each servo. This servo controller is also compatible with the Scott Edwards MiniSSC II servo controller and any software written for it.

The back side of the board has all of the ports labeled, and two mounting holes allow you to secure the controller to your project. The logic supply and the servo supply can be tied together for single-battery operation, or the on-board voltage regulator allows the logic supply to be as high as 16V.

Features:

* 8 servo ports
* 0.5us (about 0.05 degrees) resolution
* 250-2750 us range
* 5-16VDC Logic supply
* 0-5VDC Data voltage
* 50Hz pulse rate
* 1200-38400 (auto detected) serial baud rate
* 5mA average current

Dimensions: 0.91x0.91"

Documents:

* Users Guide
* Basic Stamp Example
* .NET Example

The default firmware runs simply enough: plug it in to a USB port on your computer, after the computer recognizes the device as a keyboard it will automatically start reporting the voltages. To get a series of measurements, open up a text or spreadsheet editor and plug the AVR stick in. The AVR Stick will automatically start inputting the voltage values to whatever program is active on the computer. The ADC is configured to use a 2.56V reference voltage, so don't try measuring anything higher than that without modifying the code!

This thing is meant to be hacked! Visit the Objective Development website to learn how others have used the USB stack to implement miscellaneous HID projects like keyboards, mice, joysticks, etc., etc., etc...

Documents:

* Schematic
* Firmware (AVR Stick-v12)
* Eagle Files

You may notice there are very few resistors in this kit. We recommend purchasing the resistor kit listed below for all the resistor values you may need.

Included Components:

* 1 - Parts Box
* 10 - 0.1uF cap
* 5 - 100uF cap
* 5 - 10uF cap
* 5 - 1uF cap
* 5 - 10nF cap
* 5 - 1nF cap
* 5 - 100pF cap
* 5 - 10pF cap
* 5 - 1N4148 Diode
* 5 - 1N4001 Diode
* 5 - 2N3906 PNP Transistor
* 5 - 2N3904 NPN Transistor
* 3 - 20 pin female header
* 3 - 20 pin male header
* 3 - Mini power switch
* 2 - Push buttons
* 2 - 10k trimpot
* 2 - LM358 OpAmp
* 2 - 3.3V regulator
* 2 - 5V regulator
* 1 - 555 Timer
* 1 - Green LED
* 1 - Yellow LED
* 1 - Red LED
* 1 - 7 segment Red LED
* 1 - mini Photocell

All of the pins on the bobbin protoboard are shorted together with 10mil traces. This allows for quick and easy prototyping - all you have to do is cut the traces between holes you don't want connected! Pins are spaced by a standard, 0.1" pitch.

Dimensions:

* Overall: 1.23x0.91"
* Thin 0.8mm PCB

Dimensions:

* 7.75x18.1mm
* Thin 0.8mm PCB

Documents:

* Schematic

Dimensions:

* 20mm outer diameter
* Thin 0.8mm PCB

Dimensions:

* 50mm outer diameter
* Thin 0.8mm PCB

This board has a JST connector, which will connect to our JST terminated single cell 3.7V LiPo batteries. It also has terminals for charging the LiPo battery with one of our LiPo chargers.

Dimensions:

* 18mm outer diameter
* Thin 0.8mm PCB

Documents:

* Schematic

Dimensions:

* 20mm outer diameter
* Thin 0.8mm PCB

Documents:

* Schematic
* MCP9700 Datasheet

Dimensions:

* 8x16mm
* Thin 0.8mm PCB

Documents:

* Schematic

Dimensions:

* 5x11mm
* Thin 0.8mm PCB

Documents:

* Schematic
* LED Datasheet

Dimensions:
* 20mm outer diameter
* Thin 0.8mm PCB

Documents:
* Schematic

Kit includes:
* LilyPad Mainboard 328
* LilyPad Power Supply
* FTDI Basic Breakout
* Mini USB Cable

Please note: This is an inductive buzzer meaning that is will act as a short to ground if you are not actively driving it. We recommend you put both I/O pins to low (0V) when the buzzer is not used.

Comes with 5 of each value: 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 8.2, 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82, 100, 120, 150, 180, 220, 270, 330, 390, 470, 560, 680, 820, 1K, 1.2K, 1.5K, 1.8K, 2.2K, 2.7K, 3.3K, 3.9K, 4.7K, 5.6K, 6.8K, 8.2K, 10K, 12K, 15K, 18K, 22K, 27K, 33K, 39K, 47K, 56K, 68K, 82K, 100K, 120K, 150K, 180K, 220K, 270K, 330K, 390K, 470K, 560K, 680K, 820K, 1M

A simple 'TV Out' shield for the Arduino:

• PAL or NTSC Composite Video
• 38x25 characters
• Black and White
• Runs on a 16Mhz Mega8/88/168/328p
• 300 to 57k6 baud (8n1)
• Optional Autobauding
• Simple Graphics
• Double width / height text
• VT52 + H19 control codes

The kit is composed from:

• 1 MEGA Proto shield bare PCB
• 1 40 way male 0.1" strip
• 1 40x2 way male 0.1" strip
• 2 pushbuttons
• 5 220 Ohm resistors
• 5 1K Ohm resistors
• 5 10K Ohm resistors
• 3 LEDs

Arduino MEGA Board not included

Base Level is made of:

• 1 USB cable
• 1 Straight single line pinhead connectors 2,54 40x1
• 1 Breadboard, 840 tie points
• 1 Set of 70 breadboard jumper wires
• 5 10K Ohm Resistors 1/4W
• 5 2.2K Ohm Resistor 1/4 W
• 10 220 Ohm Resistors 1/4W
• 5 330K Ohm Resistors 1/4W
• 5 100nF capacitor polyester
• 5 10nF capacitor polyester
• 3 100uF electrolytic capacitor 25Vdc
• 1 4,7K Ohm Thermistor
• 1 70..100K Ohm LDR VT90N2
• 3 5mm RED LED
• 1 5mm GREEN LED
• 1 5mm YELLOW LED
• 1 10Kohm linear potentiometer, pcb terminals
• 2 BC547 Transistor in TO92 Package
• 1 Piezo buzzer
• 5 PCB Pushbutton, 12x12mm size
• 2 4N35 Optocoupler DIL-6 package
• 2 Tilt sensor
• 1 Diode 1n4007
• 1 MOS Irf540

• 128KB of Flash
• 8KB RAM
• 4KB EEPROM

It has 53 IO (including 4 HW UARTs, 14 PWMs, I2C bus) and 16 Analog Input pins.
It can mount and use most of the Arduino Shields (not the ETH actual version).

The Zigbee module is the NEW Maxstream Series 2 XBee™ ZigBee OEM RF Module with on board chip antenna, up to 100m distance transmission .

Board comes fully assembled and tested (without Arduino board)

The kit is composed from:

• 1 Protoshield bare PCB
• 1 40 way with long terminal 0.1" strip
• 1 3x2 way male 0.1" strip
• 2 pushbuttons
• 5 220 Ohm resistors
• 5 1K Ohm resistors
• 5 10K Ohm resistors
• 3 LEDs

Arduino Board not included.

You can find some more info about how to solder the board here:
http://www.adafruit.com/images/large/protoshieldon_LRG.jpg
http://www.sgbotic.com/products/datasheets/development/proto_shield_v4_pcb.pdf
http://www.sgbotic.com/products/datasheets/development/proto_shield_v4_sch.pdf

Parts supplied:

• 1- Cable
• 1- 4way right angle connector

LilyPad and USB/serial converter should be bought apart.

The board is based on the ATmega168V (the low-power version of the ATmega168). Board will run from 2V to 5V.

It is small, complete, and breadboard friendly. It has everything that Diecimila has (electrically) with more analog input pins and onboard +5V AREF jumper.
Physically, it is missing power jack and power select jumper.

Since the Nano is automatically sense and switch to the higher potential source of power, there is no need for the power select jumper.

Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP,PD).

Duemilanove is the enhanced release of Diecimila version. It adds to the previous new features (autoreset function, extended power connector, built in led, USB overcurrent protection) the automatic power selection.

Board comes fully assembled and tested with ATMega328 pre-loaded with bootloader.